How to Calibrate Monitor Colors Without a Colorimeter
A new monitor arrives, you plug it in, and the colors look wrong in a way that is hard to describe.

A new monitor arrives, you plug it in, and the colors look wrong in a way that is hard to describe. Skin tones are a bit orange, greys have a blue cast, dark scenes in games turn into a muddy black where you cannot see anything in the corners. Or you have two screens side by side and the same white window looks cream on one and icy on the other.
The usual answer online is "buy a colorimeter", a small sensor that costs between 150 and 300 dollars. For photographers and video editors that is good advice. For most people who game, browse and watch films, it is overkill. You can get most of the way to a clean, consistent picture with the monitor's own menu, a few settings in Windows and your graphics driver, and about 20 minutes. I went through this on three monitors at home, a budget 24 inch IPS, a 27 inch VA gaming panel and an older office screen, and the steps below are what made a visible difference on all three.
Fix the settings that sabotage color first
Before any calibration, remove the things that distort the picture. On most monitors these are switched on out of the box because they look punchy in a shop.
Open the monitor's on screen menu with the buttons or joystick at the back or bottom edge. Look for a picture mode or preset. Names vary: Standard, sRGB, User, Custom, FPS, Cinema. If there is an sRGB mode, try it first. It usually clamps the color range to what Windows and most games expect, which fixes oversaturated reds and greens on wide gamut panels. The downside is that sRGB mode often locks brightness. If it does, choose User or Custom instead.
Then turn off anything with the words dynamic, eco, smart, black stabilizer or super resolution. Dynamic contrast changes brightness scene by scene, which makes calibration impossible. Eco modes dim the screen in ways that shift color. Black stabilizer in gaming modes lifts dark areas so you can spot enemies, but it washes out every other image.
The HDMI range problem nobody mentions
This one catches a surprising number of people, and it is the single biggest cause of grey, washed out blacks that I see on PC setups. Over HDMI, many graphics drivers send a limited range signal, meaning black is sent as level 16 instead of 0 and white as 235 instead of 255. Televisions expect that. Most PC monitors do not, so blacks look grey and the whole image looks flat.
On NVIDIA cards, open NVIDIA Control Panel, go to Change resolution, scroll down, choose Use NVIDIA color settings, and set Output dynamic range to Full. On AMD, open Adrenalin, go to Display, and set Pixel Format to RGB 4:4:4 Full RGB. Intel Graphics Command Center has a similar Quantization Range option under Display, Color.
DisplayPort connections are almost always full range already, which is one reason I prefer DisplayPort for a desktop monitor when the card has a free port.
Running a calibration by eye
With the distortions removed, you can do a reasonable calibration by eye. Do it in the lighting you normally use the PC in, after the monitor has been on for at least 30 minutes, because panels shift slightly as they warm up.
- Set brightness first. For a room with normal lamp lighting, aim for a white screen that is comfortable to look at, not glowing. On most 250 to 350 nit monitors that lands between 25 and 45 on the brightness slider.
- Set color temperature. Pick the preset labelled 6500K, Warm or Normal in the monitor menu. Cool or 9300K looks crisp at first but is too blue for long sessions.
- Type dccw into the Windows Start menu and open Calibrate display color. It walks you through gamma, brightness, contrast and color balance with reference images. For gamma, adjust until the small dots in the middle of the circles blend into the background.
- On the color balance step, if greys look tinted, adjust the red, green and blue sliders in the monitor's own menu, in small steps of 2 or 3, until a neutral grey looks neutral. Then finish in dccw without touching its sliders.
- Save the calibration when Windows asks. It creates a profile that loads at sign in.
The Lagom LCD monitor test pages are also worth searching for. They are free, run in a browser, and have clear patterns for black level, white saturation and gamma that make each setting easier to judge.
Downloading an ICC profile for your model rarely helps
A popular tip is to find an ICC profile for your exact monitor model from a review site and install it. I tried this on all three of my monitors, using profiles from well known reviewers. On one it improved things slightly. On the other two it made the picture worse, with a green tint on the VA panel that I could not get rid of without deleting the profile.
The reason is panel variance. Two monitors with the same model number can come from different panel batches, and a profile measured on someone else's unit, under their settings, with their graphics card, does not describe yours. A profile only works if every setting matches exactly, including brightness, preset and color temperature. Even then, the gains are small compared with fixing the HDMI range and picking the right preset. I would skip downloaded profiles unless you have the same settings documented down to the last slider.
Matching two monitors
Two screens that do not match are more distracting than one that is slightly off. Pick the better monitor as the reference and calibrate it first. Then put the same white window across both screens and adjust the second monitor's brightness and color sliders until the whites look as close as you can get them.
Perfect matching is often not possible, especially between an IPS and a VA panel, or between two different brands. Get the whites close and the brightness equal, and accept small differences in saturation. If you are still planning a two screen setup, the guide on setting up a dual monitor workspace covers positioning and scaling as well.
When a colorimeter is worth it
If you edit photos for print, grade video, or sell design work, a colorimeter such as a Calibrite Display Plus or Datacolor SpyderX pays for itself. It measures what the panel actually does and builds a correct profile in about 10 minutes. For everyone else, the steps above usually get 80 to 90 percent of the visible improvement. If your monitor still looks bad after all of this, the panel itself may be the limit, and it might be time to read about when a monitor upgrade makes sense.
FAQ
Is Windows Calibrate display color accurate?
It is accurate enough for gaming and everyday use, because it relies on your eyes rather than a sensor. It will not match a colorimeter for print or video work.
Why do blacks look grey on my PC monitor?
The most common cause is a limited range signal over HDMI. Set the output to Full range in your NVIDIA, AMD or Intel graphics settings.
Should I use the sRGB mode on my monitor?
Usually yes for games and browsing, especially on wide gamut panels. If it locks brightness too high or too low, use a custom mode instead.
How often should I recalibrate a monitor?
Once every few months is plenty for most people, or after a driver reinstall, since that can reset the HDMI range and color settings.
More in Tips
Tips
How to Back Up PC Game Saves Before Something Breaks
A reader wrote to me last spring after his boot drive died without warning.
Tips
How to Fix Stuttering in PC Games Without New Hardware
Your frame counter says 90 fps, yet the game still hitches every few seconds, as if someone keeps tapping the pause button.
Tips
How to Find the Right Mouse DPI and Sensitivity for Games
Your crosshair either flies past the target or crawls across the screen, and every time you change the setting it feels wrong...